Test, troubleshoot, repair, maintain, and integrate RF, microwave, and electronic warfare systems and hardware.
Operate RF test equipment and diagnose failures from system level through circuit card assembly and component level.
Configure test setups, conduct experiments, collect technical data, and support test method and equipment development.
Repair, fabricate, install, and modify cables, modules, assemblies, and electronic hardware; support engineering design, integration, testing, and failure analysis.
Summarised from the posting by AI and can be wrong. The full description is the source.
Requirements
Licenses and certifications
Drone pilot license, Part 107, or desire to obtain one (preferred)
IPC solder certification or equivalent qualification (preferred)
Experience
10 years of related experience in electronics technology, test and measurement, RF systems, or Electronic Countermeasure systems
5 years as an engineering technician supporting electrical design and system- or board-level troubleshooting
Hands-on experience with RF test equipment, including oscilloscopes, spectrum analyzers, signal sources, VNAs, and related instrumentation
Experience troubleshooting system-, CCA-, and component-level analog, digital, RF, power, and interface circuitry
Demonstrated soldering and surface-mount rework experience
Experience supporting complex RF/EW laboratory, field, or range testing (preferred)
Experience training or directing junior technicians (preferred)
UAV or tactical vehicle operations experience (preferred)
Education
High school diploma, vocational degree, or GED
Skills
Ability to read schematics, CCA layouts, engineering drawings, and test requirements
Proficiency with MS Office
On the job
Work outdoors and in inclement weather
Lift more than 20 pounds
Other requirements
Must be able to obtain and maintain a Top Secret/SCI security clearance
U.S. Citizenship
Travel up to 50%
Your match
Sign in and add your resume to see which of this job's requirements it shows.
Saved to your account, encrypted. The AI that reads it doesn't keep it or train on it.
Full job description
From SAIC’s careers site
Position - Senior Electronics Technician (542)
Job Description
The Senior Electronics Technician provides technical support to the Expeditionary Electromagnetic Warfare division at NSWC Crane. The role is responsible for testing, troubleshooting, repairing, maintaining, and integrating RF, microwave, and electronic warfare hardware across laboratory, range, and field environments.
Duties
Test, troubleshoot, repair, and maintain RF, microwave, and EW systems.
Operate RF test equipment including spectrum analyzers, signal generators, oscilloscopes, vector network analyzers, and related instrumentation.
Show full descriptionShow less
Diagnose hardware failures from the system level through Circuit Card Assembly (CCA) and component level, including analog, digital, RF, power, and interface circuitry.
Read and interpret schematics, CCA layouts, drawings, test requirements, and technical instructions.
Configure test setups, conduct experiments, collect technical data, and support development or improvement of test methods and special test equipment.
Repair, fabricate, install, and modify cables, modules, assemblies, and electronic hardware.
Support engineers during design, integration, testing, and failure-analysis activities.
Provide technical support during laboratory, field, and range testing.
Participate in planning meetings, IPTs, and test-event scheduling.
Support field operations as required, including UAV or tactical vehicle activities; travel up to 50%, work outdoors/in inclement weather, and lift more than 20 pounds.
Required Qualifications
High school diploma, vocational degree, or GED.
Ten (10) years of related experience in electronics technology, test and measurement, RF systems, or Electronic Countermeasure systems.
Minimum five (5) years as an engineering technician supporting electrical design and system or board-level troubleshooting.
Hands-on experience with RF test equipment including oscilloscopes, spectrum analyzers, signal sources, VNAs, and related instrumentation.
Experience troubleshooting system, CCA, and component-level analog, digital, RF, power, and interface circuitry.
Ability to read schematics, CCA layouts, engineering drawings, and test requirements.
Demonstrated soldering and surface-mount rework experience.
Ability to work independently and exercise sound technical judgment.
Strong communication skills, work independently, and proficiency with MS Office.
Must be able to obtain and maintain a Top Secret/SCI security clearance. U.S. Citizenship is required.
Desired Qualifications
Posses Drone Pilots license – Part 107 or desire to obtain license
IPC solder certification or equivalent qualification.
Experience supporting complex RF/EW laboratory, field, or range testing.
Experience training or directing junior technicians.