Electrical Engineer jobs

Product Compliance and Test Engineer

FortiveEverett, WAHybridPosted 1 month ago

Pay not listed

Key facts

Experience
7+ years
Degree
Bachelor's degree

Looks real. 1 thing to check before you apply.

On Fortive’s own careers site (Oracle Recruiting), checked open today.

  • To check: No pay range listed, though one is likely required in WAAsk for the pay range before you interview. The law here likely requires one.
  • Checked: On the company's own careers siteOracle Recruiting board
  • Checked: Checked open todayOracle Recruiting board
  • Checked: No reposts foundOracle Recruiting board
  • Trust score 90 / 100 · Strong
See all 5 checksShow fewer
How we check

What you’ll do

  • Review new and existing product designs and legacy equipment against applicable standards.
  • Define test requirements, prepare and conduct test plans, evaluate test conditions and results, and document work in compliance with ISO 17025.
  • Analyze component failures and recommend corrective actions, alternate components, or design changes; prepare and defend reports for certification bodies.
  • Select, design, and maintain laboratory test equipment, procedures, and work instructions.

Summarised from the posting by AI and can be wrong. The full description is the source.

Requirements

Experience

  • Minimum 7 years of experience in product safety or EMC evaluation, electronics design, or relevant laboratory work towards product compliance safety evaluation
  • Experience with a third-party certification body such as UL, CSA, TUV, or Intertek (preferred)
  • Experience with IEC 80079-34 and IEC 60079-0/11 for intrinsically safe designs (preferred)

Education

  • Bachelor's degree in Electrical Engineering or higher; other engineering or physical science degrees may be acceptable with suitable relevant experience (preferred)

Skills

  • Solid understanding of basic physics and physical concepts, including electrical, mechanical, and thermal concepts
  • Strong background using a wide variety of test equipment and selecting appropriate equipment for each task or measurement with limited assistance
  • Comfort analyzing schematics and wiring diagrams to understand circuit function, potential failure sources, and hazard-protection components and subsystems
  • Basic understanding of metrology and interpreting laboratory equipment specifications and measurement suitability
  • Basic electronics skills, including op-amp, diode, and transistor circuit analysis, power transformers, and switching power supplies
  • Comfort understanding, interpreting, and applying generalized test procedures and standards to varied product applications
  • Strong background in MS Office and other software tools; experience formatting and manipulating documents is a must
  • Able to disassemble and reassemble sophisticated test, measurement, and laboratory equipment without instructions or damage
  • Comfortable training other associates on laboratory equipment use
  • Working knowledge of high-frequency RF (preferred)
  • Document automation, template creation, VBA, or macro writing experience (preferred)
  • LabView experience (preferred)

On the job

  • Comfort working around high voltage, high temperature, high pressure, flammable materials, and other potentially hazardous test environments while following safety precautions

Your match

Sign in and add your resume to see which of this job's requirements it shows.

Sign in to check your match

Saved to your account, encrypted. The AI that reads it doesn't keep it or train on it.

Benefits

Flexible schedule
Opportunity to work from home 2 days per week, depending on laboratory workload requirements.

Full job description

From Fortive’s careers site

Responsibilities:

  • Review and evaluate new product designs, support engineering changes to existing designs, and evaluate legacy equipment against constantly evolving standards.
  • Determine functional, environmental, and/or compliance test requirements and applicability of tests, equipment, and facilities. Build and complete test plans and document results in compliance with ISO 17025.
  • Evaluate progress of tests for validity of test conditions, means of measurement and performance of components or equipment in relation to specifications or requirements of harmonized standards. Familiarity with IEC 61010 (safety) and IEC 61326 (EMC) standards.
Show full descriptionShow less
  • Review and document test results; take corrective action as needed. Analyze component failures; recommend alternate components or design changes.
  • Author and defend test reports submitted international certification bodies such as CSA and ETL.
  • Specify, select and/or design laboratory test equipment vital to complete equipment assessment; assist in preparation of documents to enable fabrication of new test equipment; write operating/verification procedures for new laboratory equipment and build preventative maintenance procedures and schedules. Create laboratory work instruction for use by others.
  • (optional) Support for Ex Quality Management system requirements of equipment intended for use in explosive atmospheres including factory work instruction review, production audits, ECO review against certification documents, component incoming inspection guides etc. Experience with IEC 80079-34, IEC 60079-0, 11 for intrinsically safe designs a plus.
  • (optional) opportunity for software development towards hardware interface, control, data collection, and reporting to assist in laboratory testing needs. Experience with LabView a plus.
  • Normal office and laboratory environments. Extra hours may be required for meeting commitments but should be considered atypical. Opportunity to work from home 2 days per week depending on laboratory workload requirements. Travel less than 5%. Potential international travel to standards meetings.

Qualifications:

  • Bachelor's degree in Electrical Engineering or higher recommended. Other engineering/physical science degrees may be acceptable with suitable laboratory or other relevant electrical/electronics experience per below.
  • Minimum 7 years of experience in product safety or EMC evaluation, electronics design, or relevant laboratory work towards product compliance safety evaluation. Experience with third party certification house such as UL, CSA, TUV, Intertek etc a plus.
  • Solid understanding of basic physics and physical concepts a necessity including ac/dc voltage, electrical current, resistance, inductance, capacitance, power, energy, force, acceleration, temperature, pressure, heat transfer, etc. Working knowledge of high frequency RF a plus.
  • Strong background using a wide variety of test equipment including multimeters, calibrators, oscilloscopes, signal generators, power supplies, spectrum analyzers, current clamps, and thermometers with an understanding of their capabilities and limitations. Able to select the proper equipment for each task/measurement with limited assistance.
  • Comfortable with work around high voltage, high temperature, high pressure, flammable materials, and other potentially hazardous test environments where appropriate safety precautions must be rigorously followed.
  • Comfortable analyzing schematics and wiring diagrams to understand basic concepts of circuit function, potential sources of failure, and components and subsystems relied upon for protection against hazards.
  • Basic understanding of metrology and how to interpret laboratory equipment specifications and suitability for measurement needs.
  • Basic electronics skills including opamp, diode, transistor circuit analysis, power transformers and switching power supplies.
  • Comfortable with understanding, interpreting, and applying generalized test procedures and standards to wide variety of specific product applications.
  • Strong background in MS Office and other software tools including Teams, Word, Excel, Outlook, PowerPoint, Access, SharePoint, Miro etc.) experience in formatting and document manipulation a must. Document automation, template creation, VBA and macro writing experience a benefit.
  • Strong language and communication skills including technical writing, user documentation review and editing along with clear and concise communication through email, MS Teams, phone conversations, and instant messaging.
  • Should be able to disassemble and reassemble sophisticated test and measurement and laboratory equipment without instructions or damaging the equipment to facilitate design review, prep for laboratory testing and failure analysis.
  • Comfortable training other associates on use of laboratory equipment. ‘See one, do one, teach one’ mentality.

Something wrong with this job? Report it · This flag looks wrong

Similar jobs nearby

Principal Engineer

Greenpoint Technologies · Bothell, WA

$150k–$206k/yr

StrongChecked open todayPosted 9 days ago

Principal ASIC Engineer

Echodyne Corp · Kirkland, WA

$165k–$247k/yrFull-time

StrongChecked open todayPosted 15 days ago

Audio Systems Engineer

Sesame · San Francisco, CA +1 place

$175k–$280k/yrFull-timeOn-site

StrongChecked open todayPosted 24 days ago

See more like this