Welder & Fabricator jobs

MGH-ASME Hand Arc Welder

RheemMontgomery, ALOn-sitePosted 1 month ago

Pay not listed

Key facts

Experience
1+ years
Degree
Associate degree

This job is closed.

The employer took it down 14 days ago, after 5 days open. Here are similar open jobs.

  • To check: No pay range listedAsk for the pay range before you interview.
  • Checked: On the company's own careers siteOracle Recruiting board
  • Checked: No reposts foundOracle Recruiting board
  • Note: Last seen open 20 days agoLive check
  • Trust score 89 / 100 · Looks good
See all 5 checksShow fewer
How we check

Similar open jobs

MGH-Hand Arc Welder

Rheem · Montgomery, AL

On-site

StrongPay not listedChecked open todayPosted 1 month ago

MGH-Projection Welder

Rheem · Montgomery, AL

On-site

StrongPay not listedChecked open todayPosted 1 month ago

Production Welder

New Flyer · Anniston, AL

Full-timeOn-site

StrongPay not listedLast seen open yesterdayPosted 18 days ago

Amerex - Welder

McWane, Inc. · Trussville, AL

Pay not listedFull-timeOn-site

Looks good2 to checkChecked open todayPosted 3 months ago

Senior Fitter Welder

Laborup · Birmingham, AL

$29–$30/hrOn-site

StrongOpen 3 monthsLast seen open yesterdayPosted 4 months ago

MIG Welder / Fabricator

Laborup · Birmingham, AL

$24–$27/hrOn-site

StrongOpen 4 monthsChecked open todayPosted 4 months ago

See more like this

What you’ll do

  • Weld metal components and repair damaged parts using electric arc-welding equipment and specified instructions.
  • Set welding equipment, select and mount electrodes, position and clamp workpieces, and preheat them as needed.
  • Clean parts and remove excess weld, slag, or spatter using brushes, grinders, or arc-cutting equipment.
  • Inspect finished work for conformance to specifications, maintain housekeeping, and follow safety requirements.

Summarised from the posting by AI and can be wrong. The full description is the source.

Requirements

Licenses and certifications

  • Current ASME certification, held and maintained
  • Pass and maintain employer performance tests or standard tests required by certification standards

Experience

  • 1 to 2 years of prior work experience as a Hand Arc Welder and/or an Associate degree or Certificate in Welding Technology

Education

  • High School Diploma/GED

On the job

  • Continuous lifting of 5–25 lbs; frequent lifting of 25–60 lbs; occasional lifting of 60+ lbs
  • Frequent strain due to position and unsupported lifting
  • Use personal protective equipment, including a face shield, respirator, and protective clothing

Full job description

From Rheem’s careers site

The ASME Hand Arc Welder will serve our Water Hearer Division, located in Montgomery, AL

  • Welds together metal component parts; as specified by layout, blueprints, diagram, work order, welding procedures, or oral instructions, using electric arc-welding equipment.
  • Must be able to set and adjust welding generator to insure proper voltage output.
  • Must be able to select appropriate size and composition of electrode and properly mount in holder.
  • Repairs broken or cracked parts, fills holes and increases size of metal parts, using welding equipment.
  • Welds in flat, horizontal, or vertical position.
  • Cleans or degreases parts, using wire brush, portable grinder, or chemical bath.
Show full descriptionShow less
  • Inspects finished workpiece for conformance to specifications.
  • Chips or grinds off excess weld, slag, or spatter, using hand scraper or power chipper, portable grinder, or arc-cutting equipment.
  • Positions workpieces and clamps together or assembles in jigs or fixtures.
  • Preheats workpiece, using hand torch or heating furnace.
  • Required to pass and maintain employer performance tests or standard tests; as required by the certification standards of professional and technical associations.
  • Maintain good housekeeping in work area.
  • Observe all departmental safety requirements.
  • May be exposed to high noise levels.
  • Performs other duties as assigned.
  • High School Diploma/GED.
  • Position requires Hand Arc Welder to hold, and maintain a current ASME certification.
  • A minimum of 1 to 2 years prior work experience as a Hand Arc Welder and/or an Associate degree or Certificate in Welding Technology.
  • Continuous lifting of 5-25 lbs.
  • Frequent lifting of 25-60 lbs.
  • Occasional lifting of 60+ lbs.
  • Frequent strain due to position and unsupported lifting.
  • Position will require the use of personal protective equipment to include, but not limited to, a face shield, respirator and protective clothing.

Something wrong with this job? Report it · This flag looks wrong