Electrical Engineer jobs

Safety & Compliance Engineer

FortiveEverett, WAHybrid

Pay not listed

Key facts

Experience
3+ years
Degree
Bachelor's degree

Looks real. 2 things to check before you apply.

On Fortive’s own careers site (Oracle Recruiting), checked open today.

  • To check: Posted by the employer 4 months agoLong-open jobs are sometimes already filled. Ask when they plan to hire.
  • To check: No pay range listed, though one is likely required in WAAsk for the pay range before you interview. The law here likely requires one.
  • Checked: On the company's own careers siteOracle Recruiting board
  • Checked: Checked open todayOracle Recruiting board
  • Checked: No reposts foundOracle Recruiting board
  • Trust score 80 / 100 · Looks good
See all 6 checksShow fewer
How we check

What you’ll do

  • Review product designs and engineering changes for safety and radio compliance with applicable standards.
  • Define, conduct, and document tests; evaluate results and recommend corrective actions or design changes.
  • Prepare and defend test reports and coordinate with certification bodies and third-party laboratories to obtain and maintain certifications.
  • Plan radio certification timelines and costs, and advise on radio module suitability and global market access.

Summarised from the posting by AI and can be wrong. The full description is the source.

Requirements

Experience

  • Minimum 3 years of experience in product safety, RF compliance or EMC evaluation, electronics design, or relevant laboratory work toward product compliance safety evaluation
  • Experience using multimeters, calibrators, oscilloscopes, signal generators, power supplies, spectrum analyzers, current clamps, and thermometers, and selecting suitable equipment for measurements
  • Experience with third-party certification laboratories such as UL, CSA, TUV, or Intertek (preferred)

Education

  • Bachelor's degree or higher in Electrical Engineering (preferred)

Skills

  • Program management skills to drive certification labs, prioritize certification requirements, and achieve deadlines
  • Working knowledge of RF and wireless technologies, including Wi-Fi, Bluetooth, and Zigbee
  • Basic understanding of metrology and laboratory equipment specifications and measurement suitability
  • Basic electronics skills, including RLC, op amp, diode, and transistor circuit analysis
  • Ability to interpret and apply generalized test procedures and standards to product applications
  • Strong background in MS Office and document formatting and manipulation
  • Technical writing and user documentation review and editing
  • Understanding of basic physics and electrical concepts, including voltage, current, resistance, inductance, capacitance, power, energy, force, acceleration, temperature, pressure, and heat transfer
  • Ability to disassemble and reassemble sophisticated test, measurement, and laboratory equipment without damaging it
  • Ability to analyze schematics and wiring diagrams to understand circuit function, failure sources, and hazard-protection components
  • Document automation, template creation, or VBA, Python, or macro writing experience (preferred)
  • Working knowledge of high-frequency RF (preferred)

On the job

  • Ability to work safely in test environments involving high voltage, high temperature, high pressure, or flammable materials

Your match

Sign in and add your resume to see which of this job's requirements it shows.

Sign in to check your match

Saved to your account, encrypted. The AI that reads it doesn't keep it or train on it.

Benefits

Flexible schedule
Opportunity to work from home 2 days per week, depending on laboratory workload requirements.

Full job description

From Fortive’s careers site

Safety & Radio Compliance Test Engineer

The Fluke Product Compliance team is seeking a Safety/Radio Test Engineer to protect business growth by accessing, testing and obtaining relevant certificates for new and existing products. Fluke is the world leader in professional electronic test tools and software; your work will help keep the world up and running by developing and sustaining rugged, reliable, and safe test and measurement tools used by professionals in critical and fast-growing industries such as solar power and electric vehicle service equipment.

Reporting to the manager of the Product Compliance Team your responsibilities will be as follows.

Responsibilities:

Show full descriptionShow less
  • Review and evaluate new product designs, support engineering changes to existing designs, and evaluate legacy equipment against constantly evolving standards.
  • Determine functional, environmental, and/or compliance test requirements and applicability of tests, equipment, and facilities. Define and complete test plans and document results in compliance with ISO 17025.
  • Evaluate progress of tests for validity of test conditions, means of measurement and performance of components or equipment in relation to specifications or requirements of harmonized standards.
  • Review and document test results; take corrective action as needed. Analyze component failures; recommend alternate components or design changes.
  • Author and defend test reports submitted international certification bodies such as CSA and ETL.
  • Specify, select and/or design laboratory test equipment vital to complete equipment assessment; assist in preparation of documents to enable fabrication of new test equipment; write operating/verification procedures for new laboratory equipment and build preventative maintenance procedures and schedules.
  • Review and evaluate new product designs, support engineering changes to existing designs, and evaluate legacy equipment against FCC/IC/EU(RED) set of standards.
  • Work with 3rd party test laboratories to obtain accredited certifications for Radio and EMC.
  • Consult with new product introduction team to determine radio certification plan, timeline and cost.
  • Advise on suitability of selected radio module and ROI for global market access of new products in development.
  • Sustain regional radio certifications as required due to certificate expiration or changing regulations or requirements.
  • Working knowledge of RF and wireless technologies including Wi-Fi, Bluetooth, and Zigbee.
  • Basic understanding of metrology and how to interpret laboratory equipment specifications and suitability for measurement needs.
  • Basic electronics skills including RLC, op amp, diode, and transistor circuit analysis.
  • Comfortable with understanding, interpreting, and applying generalized test procedures and standards to wide variety of specific product applications.
  • Strong background in MS Office and other software tools including Teams, Word, Excel, Outlook, PowerPoint, Access, SharePoint, Miro etc.) experience in formatting and document manipulation a must. Document automation, template creation, VBA/Python/macro writing experience a benefit.
  • Strong language and communication skills including technical writing, user documentation review and editing along with clear and concise communication through email, MS Teams, phone conversations, and instant messaging.
  • Comfortable training other associates on use of laboratory equipment. ‘See one, do one, teach one’ mentality.
  • Solid understanding of basic physics and physical concepts a necessity including ac/dc voltage, electrical current, resistance, inductance, capacitance, power, energy, force, acceleration, temperature, pressure, heat transfer, etc. Working knowledge of high frequency RF a plus.
  • Strong background using a wide variety of test equipment including multimeters, calibrators, oscilloscopes, signal generators, power supplies, spectrum analyzers, current clamps, and thermometers with an understanding of their capabilities and limitations. Able to select the proper equipment for each task/measurement with limited assistance.
  • Should be able to disassemble and reassemble sophisticated test and measurement and laboratory equipment without instructions or damaging the equipment to facilitate design review, prep for laboratory testing and failure analysis.
  • Comfortable with work around high voltage, high temperature, high pressure, flammable materials, and other potentially hazardous test environments where appropriate safety precautions must be rigorously followed.
  • Comfortable analyzing schematics and wiring diagrams to understand basic concepts of circuit function, potential sources of failure, and components and subsystems relied upon for protection against hazards.
  • Normal office and laboratory environments. Extra hours may be required for meeting commitments but should be considered atypical. Opportunity to work from home 2 days per week depending on laboratory workload requirements. Travel less than 5%.

Qualifications:

  • Bachelors degree in Electrical Engineering or higher recommended. Other engineering/physical science degrees may be acceptable with suitable laboratory or other relevant electrical/electronics experience per below.
  • Minimum 3 years of experience in product safety, RF compliance or EMC evaluation, electronics design, or relevant laboratory work towards product compliance safety evaluation. Experience with third party certification laboratories such as UL, CSA, TUV, Intertek etc a plus.
  • Program management skills in driving certification labs, effectively prioritizing certification requirements and achieving deadlines.

Something wrong with this job? Report it · This flag looks wrong

Similar jobs nearby

Principal Engineer

Greenpoint Technologies · Bothell, WA

$150k–$206k/yr

StrongChecked open todayPosted 9 days ago

Principal ASIC Engineer

Echodyne Corp · Kirkland, WA

$165k–$247k/yrFull-time

StrongChecked open todayPosted 16 days ago

Audio Systems Engineer

Sesame · San Francisco, CA +1 place

$175k–$280k/yrFull-timeOn-site

StrongChecked open todayPosted 25 days ago

See more like this