Mechanical Engineer jobs

Mechanical Engineer, Thermofluids

FluidstackAustin, TX +2 placesFull-timeHybridPosted 23 days ago

$210k–$260k/yr listed by the employer

Key facts

Where
Austin, TX · San Francisco, CA · Los Angeles, CA · hybrid
Experience
10+ years

This job is closed.

The employer took it down 5 days ago, after 16 days open. Here are similar open jobs.

  • Checked: On the company's own careers siteAshby board
  • Checked: Pay listedJob posting
  • Checked: No reposts foundAshby board
  • Trust score 89 / 100 · Looks good
See all 4 checksShow fewer
How we check

Similar open jobs

Sr. Mechanical Engineer

Stream Data Centers · Remote · US only

$200k–$240k/yrFull-time

StrongLast seen open yesterdayPosted 1 month ago

See more like this

What you’ll do

  • Develop cycle models to define working fluids, pressures, temperatures, and flows for compressors, turbines, and heat exchangers.
  • Design large heat exchangers and the surrounding piping, valves, headers, relief, and isolation systems.
  • Evaluate machine operating points using coupled exchanger ratings and trades such as air-side temperature rise, face velocity, and subcooling.
  • Validate cycle predictions against test-stand measurements, including measured COP, and identify model discrepancies.

Summarised from the posting by AI and can be wrong. The full description is the source.

Requirements

Experience

  • 10+ years of experience in thermofluids engineering, including thermodynamic cycle modeling, heat exchanger design, and high-pressure fluid system design
  • Built a thermodynamic cycle model from fluid properties and defended its assumptions
  • Sized real heat exchangers against published correlations and assessed whether the correlations matched the exchanger geometry
  • Calibrated a model against machine datasheet or test data and reported the gap
  • Written analysis that changed a design decision and could be understood and acted on by people who did not run the code
  • Sized a relief path and signed off that the system was protected
  • Propulsion and cryogenic fluid systems, including feed systems, regenerative cooling, and two-phase transport (preferred)
  • Data center thermal architecture, including CDUs, dry coolers, and direct-to-chip cooling (preferred)

Skills

  • Vapor-compression and transcritical cycles, including chillers, heat pumps, and refrigeration (preferred)
  • Piping and relief design for high-pressure fluid systems (preferred)
  • Real-gas properties and two-phase heat-transfer correlations, including CoolProp, REFPROP, Cavallini, Gnielinski, and Wang (preferred)

Other requirements

  • Regular travel of 25% or more, depending on business needs
  • Austin, TX location and working in person under a hybrid model (preferred)

Full job description

From Fluidstack’s careers site

ABOUT FLUIDSTACK

We exist to make humanity more free. For most of human history, you farmed or you starved. Technology gave people more time for the things they wanted to do, instead of things they had to do. Powerful AI will be the biggest lever for human choice we've ever built - but only if models are aligned with what humanity actually wants. There are groups building AI who don't share these goals. Whoever deploys frontier compute infrastructure fastest will decide whether AI expands human freedom or shrinks it.

Show full descriptionShow less

We're singularly focused on delivering 10 to 100s of GWs of compute faster than anyone else, rethinking every layer of the stack. We acquire power, design and build data centers, and operate them - with teams spanning hardware and software. Speed and scale are our key differentiators. Come be a part of building civilization-scale infrastructure for AI.

We hire people who care deeply about this problem space. If that is you, please apply!

HOW WE OPERATE

  • Be a barrel. Full autonomy. Own things end to end, take on scope without being asked, no permission required to operate outside your core role.
  • Insane urgency. We drive everything forward as fast as possible.
  • Reason from first principles. Challenge every assumption. Zero analogy thinking, no egos, the best idea wins.
  • Love of the game. The frontier of AI is the most interesting problem of our time. We put in long hours at high intensity to push the frontier forward.
  • Build something that actually matters. If you're going to spend your time, spend it on something that matters to the world.

THE THERMOFLUIDS R&D TEAM

Examples of key problems the team is working on

  • Reject 10s of GW of heat, starting now. Fluidstack is targeting 10s of GW of compute over the next two years. Every watt of it becomes heat that has to go somewhere, and no cooling team has ever been asked to open at that scale rather than grow into it.
  • Design and build the machines, because nobody can supply them. The merchant compressor market cannot deliver at this rate, and the vendor base behind today’s chillers will not scale to gigawatts. We are taking compressor and chiller design in house, working on machine architectures nobody sells today, and going from blank sheet to production faster than this industry thinks is possible.
  • Own every thermofluids problem behind the fleet, not just the chiller. Working fluid and cycle architecture, heat exchangers at a scale that dominates the cost of the plant, two-phase heat transfer at the chip, and thermal energy storage. All of it is open, and whatever this team lands gets built thousands of times.

ROLE SCOPE

  • Define what the machine has to be, owning the cycle model that sets the working fluid and the pressures, temperatures and flows the compressor, turbine and exchangers are designed against.
  • Design heat exchangers with surface areas running into millions of square meters, among the largest single drivers of a data center’s physical footprint.
  • Design the fluid system around the machine: piping, valves, headers, relief and isolation, sized against the pressure-drop budget the cycle can afford and the pressures the fluid actually runs at.
  • Run the trades that decide the machine: air-side temperature rise, face velocity and subcooling. Derive the operating points from coupled exchanger ratings rather than asserted approach temperatures, so infeasible designs get caught in the model instead of in hardware.
  • Take the cycle predictions onto the test stand and reconcile them against measured COP, then say plainly where the model was wrong.

WHAT WE'RE LOOKING FOR

The below is a starting point. We always make space for exceptional people, so if you don't fit this role exactly, tell us where you would https://jobs.ashbyhq.com/fluidstack/05c2e69c-42f9-4fcb-9cf0-a467aaf98f1c.

  • 10+ years of experience in thermofluids engineering, including thermodynamic cycle modeling, heat exchanger design, and high-pressure fluid system design.
  • You’ve built a thermodynamic cycle model from fluid properties up and defended its assumptions to someone actively trying to break it.
  • You’ve sized real heat exchangers against published correlations, and you’ve caught a case where the correlation belonged to a different geometry than the one in front of you.
  • You’ve calibrated a model against a machine datasheet or test data and reported the gap honestly rather than tuning until it disappeared.
  • You’ve written the analysis that changed a design decision, in a form that people who never ran the code could read and act on.
  • You’ve sized a relief path and been the one who signed off that the system was protected.
  • You’ve held a result open when it was still open, instead of closing it early to be helpful.
  • You're comfortable with regular travel: expect 25% or more, depending on business needs.
  • Most of our engineering team, stakeholders, and work are based in Austin, TX, and we value working in person. We have a strong preference for Austin and run a hybrid model, but we're open to other locations for the right role and candidate.
  • Bonus: Vapor-compression and transcritical cycles (chillers, heat pumps, refrigeration). Propulsion and cryogenic fluid systems (feed systems, regenerative cooling, two-phase transport). Piping and relief design for high-pressure fluid systems. Real-gas properties and two-phase heat-transfer correlations (CoolProp, REFPROP, Cavallini, Gnielinski, Wang). Data center thermal architecture (CDUs, dry coolers, direct-to-chip).

We are committed to pay equity and transparency.

You will receive a confirmation email once your application has successfully been accepted. If there is an error with your submission and you did not receive a confirmation email, please email careers@fluidstack.io with your resume/CV, the role you've applied for, and the date you submitted your application-- someone from our recruiting team will be in touch.

Fluidstack is an Equal Employment Opportunity Employer. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, national origin, sexual orientation, gender identity, disability and protected veterans’ status, or any other characteristic protected by law. Fluidstack will consider for employment qualified applicants with arrest and conviction records pursuant to applicable law.

Applicant Privacy Notice https://fluidstack.io/legal/applicant-privacy-notice AI Screening Notice https://fluidstack.io/legal/ai-screening-notice Ashby Bias Audit https://fluidstack.io/legal/ashby-bias-audit

Something wrong with this job? Report it · This flag looks wrong